View 3-21002-4_8706645.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

.2314#3)/. (%%3 )%"&+"& !"& '&-)*"'& "+*
& /& 7#/ ,%#31/.)#2 /10/1!3)/. !11)2"41' ,, .3%1.!3)/.!, )'(32 %2%15%$ ,/'/ !.$ 7#/ ,%#31/.)#2 !1% 31!$%-!1+2 1!$%-!1+ 3(%1 01/$4#32 ,/'/2 !.$ #/-0!.7 .!-%2 42%$ !1% 3(% 01/0%137 /& 3(%)1 1%20%#3)5% /6.%12

()2 #/.31/,,%$ $/#4-%.3 )2 24"*%#3 3/ #(!.'% /1 ,!3%23 1%5)2)/. !.$ %')/.!, 423/-%1 %15)#% 5)2)3 /41 6%"2)3% !3 ...+/'$+)'&"*'% %5 ') "&"+,) ,"#!& (($"+')* item no. part no. description qty 1 6906711 plate, base 1 2 6906722 mount, base 1 3 4210024 screw, btn hd cap, 3/816 x .500 in. l 3 4 3210006 screw, skt hd cap, no. 1032 x .625 in. l 2 5 6906732 bracket, holddown 1 6 2210007 screw, skt hd cap, no. 832 x .500 in. l 2 7 6906741 stop, rear 2 8 210094 setscrew, skt, slflkg, 1/420 x .375 in. l 1 9 6904991 ram 1 10 deleted 11 6949251* bracket assy, vertical reel ref 12 6949282 bracket, lh stock guide 1 13 4702681 guide, stock 1 14 3210001 screw, skt hd cap, no. 832 x 1.00 in. l 4 15 277083 knob, thumbscrew 2 16 210222 nut, slflkg, no. 832 1 17 4557441 shroud, end feed 1 18 4557451 guard, end feed 1 19 1218993 washer, flat, no. 8 12 20 210186 nut, hex, no. 832 7 21 7224680 screw, bdg hd, no. 832 x .375 in. l 5 22 7224683 screw, bdg hd, no. 832 x .750 in. l 1 23 222801 spring, compression 1 24 4557481 shroud, side feed 1 25 4557491 guard, side feed 1 26 3210024 screw, btn hd cap, 1/420 x .625 in. l 1 27 218993 washer, flat, 1/4 in. 1 *refer to customer manual 4095128 for the detailed parts breakdown of assembly and related parts.. figure 1
&%*"'(#&% #)(

%!

these conversion kits are used to modify ampolectric model k terminating machines to accept miniature quickchange applicators. kit no. 6906752 is required for all endfeed and those sidefeed applicators that receive the strip terminals in a horizontal position. refer to the exploded view and parts list in figure 1 to make sure you have all the parts required for the conversion. kit no. 6906752 plus kit no. 6926131 are required for those sidefeed applicators that receive the strip terminals in a vertical position. #+)."#).- -# , $(,-+.-$)(, 0# + + ! + ( $, ' -) #(1&$(" -# '#$( ( -) -# ,$ '#$( *+-, ( ,, '&$ , + ! + -) .,-)' + (.&
read the following instructions carefully before and during the installation of the conversion kits on the machine. before starting installation of the conversion kits, remove and store mechanical feed arm or air feed operation arm from feed mechanism shaft by loosening or removing clamp screws. .+$(" $(,-&&-$)( )! -# )(/ +,$)( %$- +-$( *+-, ( ,, '&$ , + ')/ ( $-# + *& $( ,-)+" )+ + -$( !)+ $(,-&&-$)( )! -# %$- #$, %$- $, ()- + )'' ( !)+ ) &, ( '#$( , -#- & -+$& *)0 + -) -# '#$( $, 1 *.&&$(" -# *&." !+)' -# + *-& #) &

%() $$ )#&% for installation of this kit, the machine must be equipped with the proper vertical reel bracket assembly (part no. 6949251). for information pertaining to this assembly, refer to customer manual 4095128. 1. the lefthand stock guide is required only when using sidefeed applicators. with guide installed on the bracket, attach the bracket to the vertical reel bracket assembly with two screws capped with knurled knobs, as shown. 2. to guide the terminal strip properly into endfeed applicators, it is necessary that the righthand stock guide bracket be lowered by using the upper hold in the vertical support for the left screw, as shown. 3. remove the two base mount screws and washers form frame and install the base mount supplied in the kit. adjust height of the base mount as low as possible in accordance with the machine manual. 4. handcycle in accordance with the machine manual until the toggle link is at its lowest position. 5. remove the arm retaining plate by removing the four screws. 6. loosen the setscrew in the ram, and then pivot the toggle link toward the front of the machine and slide out the toggle link pin to remove the ram. 7. lubricate the four sides of the new ram, supplied in the kit, as specified in the machine manual. 8. pivot the toggle link forward and install the new ram with the toggle link pin removed in step 6. pivot the ram back into position and tighten the setscrew provided in the kit. 9. install the ram retaining plate with the four screws removed in step 6. 10. handcycle the machine to the rest position (top dead center). 11. all parts removed for conversion, and any unused parts of the kit, should be retained and stored. #) &

%() $$ )#&% this kit, in addition to kit 6906752, is required only for side feed applicators that receive strip terminals in a vertical position. 1. lay out the machine frame for holes as shown in figure 3. 2. drill two size ago holes, and thread with 5/1618 unc2b tap. 3. assemble the reel support as shown and install on the machine with the two screws supplied in the kit. it is necessary for all miniature quickchange applicators, when used in an ampolectric machine, to be equipped with the correct feed cam as listed on the applicator parts list (log) supplied with the applicator. check the feed cam, and if necessary, replace it as described in the applicator instructions supplied with the applicator. retain all parts that are removed.

" ' )" &$"!% "$#"$&"! figure 2 !
"(! (refer to 4095128) see figure 3 for drilling of frame and installation of reel bracket assembly for kit no. 6926131.
%$)"&'#%$ #('

$!

figure 3
1. install the movable stop on the back of the base mount for the end feed applicator or on the left end for the side feed applicator, as shown in figure 2. 2. place the applicator on the base mount, insert the ram post in the machine ram, then slide the applicator into position against the stops. 3. secure the applicator with the holddown bracket and two screws supplied in the kit. the location of the holddown bracket differs for end feed and side feed applicators. make certain the bracket is located correctly. 4. load the applicator in accordance with the applicator instruction sheet supplied with the applicator. 5. set the wire disc and insulation disc for the wire gage to be used in accordance with the data plate on the applicator and/or the applicator parts list supplied with the applicator. 6. adjust the base mount for the correct crimp height in accordance with the machine manual. 7. install the side feed or end feed shroud and guard assembly, for the type of applicator installed, as shown in figure 2. 8. to remove the applicator from the machine, unload the applicator tooling according to the instruction sheet shipped with the applicator, remove the holddown bracket, and slide the applicator away from the stops on the base mount until the ram post is clear of the machine ram. revisions to this instruction sheet include: updated document to current requirements new format

▲Up To Search▲

Price & Availability of 3-21002-4

	To Download 3-21002-4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .